Home
Giới thiệu
Tài khoản
Đăng nhập
Quên mật khẩu
Đổi mật khẩu
Đăng ký tạo tài khoản
Liệt kê
Công trình khoa học
Bài báo trong nước
Bài báo quốc tế
Sách và giáo trình
Thống kê
Công trình khoa học
Bài báo khoa học
Sách và giáo trình
Giáo sư
Phó giáo sư
Tiến sĩ
Thạc sĩ
Lĩnh vực nghiên cứu
Tìm kiếm
Cá nhân
Nội dung
Góp ý
Hiệu chỉnh lý lịch
Thông tin chung
English
Đề tài NC khoa học
Bài báo, báo cáo khoa học
Hướng dẫn Sau đại học
Sách và giáo trình
Các học phần và môn giảng dạy
Giải thưởng khoa học, Phát minh, sáng chế
Khen thưởng
Thông tin khác
Tài liệu tham khảo
Hiệu chỉnh
Số người truy cập: 107,145,091
Experimental Investigation on the Buckling Capacity of Angle Steel Strengthened at Both Legs Using VaRTM-Processed Unbonded CFRP Laminates
Tác giả hoặc Nhóm tác giả:
Fengky Satria Yoresta, Phan Viet Nhut, Daiki Nakamoto, Yukihiro Matsumoto
Nơi đăng:
Polymers (SCIE);
S
ố:
2021, 13(13), 2216;
Từ->đến trang
: 1-18;
Năm:
2021
Lĩnh vực:
Kỹ thuật;
Loại:
Bài báo khoa học;
Thể loại:
Quốc tế
TÓM TẮT
Strengthening steel structures by using carbon fiber reinforced polymer (CFRP) laminates showed a growth trend in the last several years. A similar strengthening technique, known as adhesive bonding, has also been adopted. This paper presented a promising alternative for strengthening steel members against buckling by using vacuum-assisted resin transfer molding (VaRTM)-processed unbonded CFRP laminates. A total of thirteen slender angle steel members (L65x6), including two control specimens, were prepared and experimentally tested. The specimens were strengthened only at both legs and were allowed to buckle on their weak axes. The test showed that the unbonded CFRP strengthening successfully increased the buckling capacity of the angle steel. The strengthening effect ranged from 7.12% to 69.13%, depending on various parameters (i.e., number of CFRP layers, CFRP length, and angle steel’s slenderness ratio). Flexural stiffness of the CFRP governed the failure modes in terms of location of plastic hinge and direction of buckling curvature.
ABSTRACT
Strengthening steel structures by using carbon fiber reinforced polymer (CFRP) laminates showed a growth trend in the last several years. A similar strengthening technique, known as adhesive bonding, has also been adopted. This paper presented a promising alternative for strengthening steel members against buckling by using vacuum-assisted resin transfer molding (VaRTM)-processed unbonded CFRP laminates. A total of thirteen slender angle steel members (L65x6), including two control specimens, were prepared and experimentally tested. The specimens were strengthened only at both legs and were allowed to buckle on their weak axes. The test showed that the unbonded CFRP strengthening successfully increased the buckling capacity of the angle steel. The strengthening effect ranged from 7.12% to 69.13%, depending on various parameters (i.e., number of CFRP layers, CFRP length, and angle steel’s slenderness ratio). Flexural stiffness of the CFRP governed the failure modes in terms of location of plastic hinge and direction of buckling curvature.
© Đại học Đà Nẵng
Địa chỉ: 41 Lê Duẩn Thành phố Đà Nẵng
Điện thoại: (84) 0236 3822 041 ; Email: dhdn@ac.udn.vn