Home
Giới thiệu
Tài khoản
Đăng nhập
Quên mật khẩu
Đổi mật khẩu
Đăng ký tạo tài khoản
Liệt kê
Công trình khoa học
Bài báo trong nước
Bài báo quốc tế
Sách và giáo trình
Thống kê
Công trình khoa học
Bài báo khoa học
Sách và giáo trình
Giáo sư
Phó giáo sư
Tiến sĩ
Thạc sĩ
Lĩnh vực nghiên cứu
Tìm kiếm
Cá nhân
Nội dung
Góp ý
Hiệu chỉnh lý lịch
Thông tin chung
English
Đề tài NC khoa học
Bài báo, báo cáo khoa học
Hướng dẫn Sau đại học
Sách và giáo trình
Các học phần và môn giảng dạy
Giải thưởng khoa học, Phát minh, sáng chế
Khen thưởng
Thông tin khác
Tài liệu tham khảo
Hiệu chỉnh
Số người truy cập: 107,116,279
Pin‐bearing connection strength of single‐bolted pultruded glass fiber‐reinforced polymer profiles strengthened by glass fiber sheet
Tác giả hoặc Nhóm tác giả:
Phan Viet Nhut, Quang Duc Tran, Yukihiro Matsumoto
Nơi đăng:
Polymer composites (SCIE);
S
ố:
Volume 43, Issue 8;
Từ->đến trang
: 5011-5030;
Năm:
2022
Lĩnh vực:
Kỹ thuật;
Loại:
Bài báo khoa học;
Thể loại:
Quốc tế
TÓM TẮT
This study's aim was to research the ultimate loads and failure modes of single-bolted pultruded glass-fiber-reinforced polymer (PGFRP) connections reinforced by glass fiber sheets (GFSs) under pin-bearing conditions. In total, 144 specimens with various geometric parameters of GFRP bolted connections with different ratio values of the end distance of PGFRP plate to bolt diameter (e/d) and various ratio values of width of PGFRP plate to bolt diameter (w/d) were considered, and their results are here discussed (e/d = 2,3,4 and w/d = 2,3,4,5). Three types of GFSs (0°/90° GFSs, ±45°GFSs, and chopped strand mat GFSs) were molded by the vacuum-assisted resin transfer molding (VaRTM) method and used to strengthen the connections. The results show that all three types of GFSs had good effects on the increase in the ultimate load of the connections. In addition, the strengthening effects were decreased with the increase in the e/d ratio of the connections for all types of GFSs. Moreover, theoretical equations were suggested to forecast the ultimate loads and failure modes of pin-bearing single GFS-strengthened PGFRP connections with high accuracy (less than 12% deviation).
ABSTRACT
This study's aim was to research the ultimate loads and failure modes of single-bolted pultruded glass-fiber-reinforced polymer (PGFRP) connections reinforced by glass fiber sheets (GFSs) under pin-bearing conditions. In total, 144 specimens with various geometric parameters of GFRP bolted connections with different ratio values of the end distance of PGFRP plate to bolt diameter (e/d) and various ratio values of width of PGFRP plate to bolt diameter (w/d) were considered, and their results are here discussed (e/d = 2,3,4 and w/d = 2,3,4,5). Three types of GFSs (0°/90° GFSs, ±45°GFSs, and chopped strand mat GFSs) were molded by the vacuum-assisted resin transfer molding (VaRTM) method and used to strengthen the connections. The results show that all three types of GFSs had good effects on the increase in the ultimate load of the connections. In addition, the strengthening effects were decreased with the increase in the e/d ratio of the connections for all types of GFSs. Moreover, theoretical equations were suggested to forecast the ultimate loads and failure modes of pin-bearing single GFS-strengthened PGFRP connections with high accuracy (less than 12% deviation).
© Đại học Đà Nẵng
Địa chỉ: 41 Lê Duẩn Thành phố Đà Nẵng
Điện thoại: (84) 0236 3822 041 ; Email: dhdn@ac.udn.vn