Home
Giới thiệu
Tài khoản
Đăng nhập
Quên mật khẩu
Đổi mật khẩu
Đăng ký tạo tài khoản
Liệt kê
Công trình khoa học
Bài báo trong nước
Bài báo quốc tế
Sách và giáo trình
Thống kê
Công trình khoa học
Bài báo khoa học
Sách và giáo trình
Giáo sư
Phó giáo sư
Tiến sĩ
Thạc sĩ
Lĩnh vực nghiên cứu
Tìm kiếm
Cá nhân
Nội dung
Góp ý
Hiệu chỉnh lý lịch
Thông tin chung
English
Đề tài NC khoa học
Bài báo, báo cáo khoa học
Hướng dẫn Sau đại học
Sách và giáo trình
Các học phần và môn giảng dạy
Giải thưởng khoa học, Phát minh, sáng chế
Khen thưởng
Thông tin khác
Tài liệu tham khảo
Hiệu chỉnh
Số người truy cập: 109,886,153
Design and Simulation of Electromagnetic Linear Actuators for Jet Dispensers
Tác giả hoặc Nhóm tác giả:
Minh-Sang Tran, Sheng-Jye Hwang
Nơi đăng:
Tạp chí xuất bản Applied Sciences;
S
ố:
10(5);
Từ->đến trang
: 1653;
Năm:
2020
Lĩnh vực:
Kỹ thuật;
Loại:
Bài báo khoa học;
Thể loại:
Quốc tế
TÓM TẮT
ABSTRACT
Three electromagnetic-based linear actuators, namely a solenoid actuator (SA), a moving coil actuator (MCA), and a moving magnet actuator (MMA), are proposed for driving the needle in a jet dispenser. The total resistance force acting on the needle during operation, including the damping force, the friction force, the inertia force, the compression spring force, and the backpressure, are measured by an experimental model. The thrust force required to overcome this resistance force is then predicted for each actuator using finite element analysis (FEA) simulations. Simple two-dimensional models of the SA, MCA, and MMA are constructed using the same coil dimensions in every case in order to facilitate an objective comparison between them. Simulations in ANSYS Maxwell software are then performed to adjust the specific dimensions of each actuator structure in such a way as to generate the thrust force required to drive the needle in the jet dispenser with the minimum excitation current possible. The simulation results show that for a maximum needle driving frequency of 250 Hz and a stroke length of 0.5 mm, the excitation current required to generate the necessary thrust force is equal to 1.8 A and 1.9 A for the MCA and MMA models, respectively, when a return spring is not used, and 2.2 A, 3.8 A, and 4.1 A for the SA, MCA, and MMA models, respectively, when a return spring is employed. It is additionally shown that the thrust force drop of the MCA and MMA models is far less than that of the SA model, about 0.7%, 1.8%, and 61% for three models, respectively. Three preliminary designs for jet dispensers incorporating the proposed actuators are also generated for reference purposes.
© Đại học Đà Nẵng
Địa chỉ: 41 Lê Duẩn Thành phố Đà Nẵng
Điện thoại: (84) 0236 3822 041 ; Email: dhdn@ac.udn.vn