Home
Giới thiệu
Tài khoản
Đăng nhập
Quên mật khẩu
Đổi mật khẩu
Đăng ký tạo tài khoản
Liệt kê
Công trình khoa học
Bài báo trong nước
Bài báo quốc tế
Sách và giáo trình
Thống kê
Công trình khoa học
Bài báo khoa học
Sách và giáo trình
Giáo sư
Phó giáo sư
Tiến sĩ
Thạc sĩ
Lĩnh vực nghiên cứu
Tìm kiếm
Cá nhân
Nội dung
Góp ý
Hiệu chỉnh lý lịch
Thông tin chung
English
Đề tài NC khoa học
Bài báo, báo cáo khoa học
Hướng dẫn Sau đại học
Sách và giáo trình
Các học phần và môn giảng dạy
Giải thưởng khoa học, Phát minh, sáng chế
Khen thưởng
Thông tin khác
Tài liệu tham khảo
Hiệu chỉnh
Số người truy cập: 107,430,202
Ultimate Bearing Capacity of Rigid Footing on Two-layered Soils of Sand-Clay
Tác giả hoặc Nhóm tác giả:
Pham N. Quang*
, Ohtsuka Satoru
Nơi đăng:
International Journal of Geomechanics (ASCE) (SCIE-Q1-IF=3.918), Doi: 10.1061/(ASCE)GM.1943-5622.0002095;
S
ố:
21 (7);
Từ->đến trang
: 04021115 (1-15);
Năm:
2021
Lĩnh vực:
Chưa xác định;
Loại:
Bài báo khoa học;
Thể loại:
Quốc tế
TÓM TẮT
ABSTRACT
This study widely investigates the ultimate bearing capacity of a rigid footing on the free surface of sand overlying clay using the rigid plastic finite element method (RPFEM). Interface elements were introduced with the new constitutive equations developed by the authors to properly evaluate the interaction between the footing and the soil, as these elements greatly affect the failure mechanism of the footing-soil system. Two friction conditions were employed for the footing surface, namely, the perfectly rough condition and the perfectly smooth condition. The RPFEM was extended to calculate the distribution of contact normal stress along the footing base corresponding to changes in the thickness of the sand layer. Several design charts were developed to directly determine the ultimate bearing capacity by increasing the internal friction angle, the thickness of the sand layer, and the shear strength of the clay layer. Two cases were considered for the clay layer below the sand layer, namely, a weak layer and a stiff layer. The failure mode of two-layered soils was found to change from the general shear mode to the punching shear mode for both friction conditions by a reduction in the shear strength of the clay layer. The sheared area of the ground was limited to the sand layer in the general shear mode, while the sheared area was distributed throughout the two layers in the punching shear mode. New bearing capacity formulas during the punching shear mode were proposed for the two friction conditions in a wide range of strength and geometric parameters, which were in close agreement with the experimental studies and are efficient enough to be used in practice
[
ultimate bearing capacity of rigid footing on two-layered soils of sand-clay.pdf
]
© Đại học Đà Nẵng
Địa chỉ: 41 Lê Duẩn Thành phố Đà Nẵng
Điện thoại: (84) 0236 3822 041 ; Email: dhdn@ac.udn.vn